Cassette tape (Redirected from Cassette tapes)

Listen to this article
Compact Cassette
A TDK SA90 Type II Compact Cassette
Media typeMagnetic tape cassette
EncodingAnalog signal, in four tracks
CapacityMost commonly 30, 45, and 60 minutes per side (C60, C90, and C120)
ReadmechanismTape head
WritemechanismTape head
DevelopedbyPhilips
UsageAudio and data storage (replaced by CD)
ExtendedfromReel-to-reel audio tape recording
ExtendedtoDigital Compact Cassette
ReleasedAugust 1963; 60 years ago (August 1963)

The Compact Cassette, also commonly called a cassette tape, audio cassette, or simply tape or cassette, is an analog magnetic tape recording format for audio recording and playback. Invented by Lou Ottens and his team at the Dutch company Philips and released in August 1963, Compact Cassettes come in two forms, either containing content as a prerecorded cassette (Musicassette), or as a fully recordable "blank" cassette. Both forms have two sides and are reversible by the user. Although other tape cassette formats have also existed—for example the Microcassette—the generic term cassette tape is normally used to refer to the Compact Cassette because of its ubiquity.

Its uses have ranged from portable audio to home recording to data storage for early microcomputers; the Compact Cassette technology was originally designed for dictation machines, but improvements in fidelity led to it supplanting the stereo 8-track cartridge and reel-to-reel tape recording in most non-professional audio applications by the mid-1970s. It became an extremely popular format for prerecorded music, first alongside the LP record and later the digital compact disc (CD); the latter format eventually caused prerecorded cassettes to fade into obscurity by the early 2000s in many countries, including the United States. The popularity of cassettes continued well into the 2000s in some other countries, including home recording purposes. Compact Cassette tapes remain in production as of 2024 and survive as an alternative to Vinyl format, continuing to receive some new music releases among popular artists.

The cassette was accompanied by two major tape playing innovations: the boombox and the Sony Walkman.

Compact Cassettes contain two miniature spools, between which the magnetically coated, polyester-type plastic film (magnetic tape) is passed and wound—essentially miniaturizing reel-to-reel audio tape and enclosing it, with its reels, in a small case (cartridge)—hence "cassette". These spools and their attendant parts are held inside a protective plastic shell which is 4 by 2.5 by 0.5 inches (10.2 cm × 6.35 cm × 1.27 cm) at its largest dimensions. The tape itself is commonly referred to as "eighth-inch" tape, supposedly 18 inch (0.125 in; 3.17 mm) wide, but actually slightly larger, at 0.15 inches (3.81 mm). Two stereo pairs of tracks (four total) or two monaural audio tracks are available on the tape; one stereo pair or one monophonic track is played or recorded when the tape is moving in one direction and the second (pair) when moving in the other direction. This reversal is achieved either by manually flipping the cassette when the tape comes to an end, or by the reversal of tape movement, known as "auto-reverse", when the mechanism detects that the tape has ended.

History

Precursors

Wollensak portable reel-to-reel tape recorder
Compact Cassette vs. RCA Tape Cartridge

After the Second World War, magnetic tape recording technology proliferated across the world. In the United States, Ampex, using equipment obtained in Germany as a starting point, began commercial production of tape recorders. First used in studios to record radio programs, tape recorders quickly found their way into schools and homes. By 1953, 1 million US homes had tape machines.

In 1958, following four years of development, RCA Victor introduced the stereo, quarter-inch, reversible, reel-to-reel RCA tape cartridge.

Introduction of mono version

Operating instructions for the Philips/Norelco Cartridge Tape Carry-Corder 150 (1964)
One of the first cassette recorders from Philips, the Typ EL 3302 (1968)
Inside of a cassette

In the early 1960s Philips Eindhoven tasked two different teams to design a tape cartridge for thinner and narrower tape compared to what was used in reel-to-reel tape recorders. By 1962, the Vienna division of Philips developed a single-hole cassette, adapted from its German described name Einloch-Kassette.

Philips selected the two-spool cartridge as a winner and introduced the 2-track 2-direction mono version in Europe on 28 August 1963 at the Berlin Radio Show, and in the United States (under the Norelco brand) in November 1964. The trademark name Compact Cassette came a year later. The team of Dutch and Belgian origin at Philips was led by the Dutch Lou Ottens in Hasselt, Belgium.

Philips also offered a machine to play and record the cassettes, the Philips Typ EL 3300. An updated model, Typ EL 3301 was offered in the US in November 1964 as Norelco Carry-Corder 150. By 1966 over 250,000 recorders had been sold in the US alone and Japan soon became the major source of recorders. By 1968, 85 manufacturers had sold over 2.4 million players. By the end of the 1960s, the cassette business was worth an estimated 150 million dollars. By the early 1970s the compact cassette machines were outselling other types of tape machines by a large margin.

Philips was competing with Telefunken and Grundig (with their DC International format ) in a race to establish its cassette tape as the worldwide standard, and it wanted support from Japanese electronics manufacturers. Philips' Compact Cassette became dominant as a result of Sony pressuring Philips to license the format to them free of charge.

In the early years sound quality was mediocre, but it improved dramatically by the early 1970s when it caught up with the quality of 8-track tape and kept improving. The Compact Cassette went on to become a popular (and re-recordable) alternative to the 12-inch vinyl LP during the late 1970s.

Stereo version

As with prerecorded reel-to-reel and 8-track, sales were slow to start, but picked up rapidly to tie with the 8-track before superseding it by the early '70s. By 1968, 85 manufacturers had sold over 2.4 million mono and stereo players. By the end of the 1960s, the cassette business was worth an estimated 150 million dollars. By the early 1970s the compact cassette machines were outselling other types of tape machines by a large margin.

Popularity of music cassettes

The mass production of "blank" (not yet recorded) Compact Cassettes began in 1964 in Hanover, Germany. Prerecorded music cassettes (also known as Music-Cassettes, and later just Musicassettes; M.C. for short) were launched in Europe in late 1965. The Mercury Record Company, a US affiliate of Philips, introduced M.C. to the US in July 1966. The initial offering consisted of 49 titles.

However, the system had been designed initially for dictation and portable use, with the audio quality of early players not well suited for music. Some early models also had an unreliable mechanical design. In 1971, the Advent Corporation introduced their Model 201 tape deck that combined Dolby type B noise reduction and chromium(IV) oxide (CrO2) tape, with a commercial-grade tape transport mechanism supplied by the Wollensak camera division of 3M Corporation. This resulted in the format being taken more seriously for musical use, and started the era of high fidelity cassettes and players.

British record labels began releasing compact cassettes in October 1967, and they exploded as a mass-market medium after the first Walkman, the TPS-L2, went on sale on July 1, 1979, as cassettes provided portability, which vinyl records could not. While portable radios and boom boxes had been around for some time, the Walkman was the first truly personal portable music player, one that not only allowed users to listen to music away from home, but to do so in private. According to the technology news website The Verge, "the world changed" on the day the TPS-L2 was released. Stereo tape decks and boom boxes became some of the most highly sought-after consumer products of both decades, as the ability of users to take their music with them anywhere with ease led to its popularity around the globe.

The Sony Walkman

Like the transistor radio in the 1950s and 1960s, the portable CD player in the 1990s, and the MP3 player in the 2000s, the Walkman defined the portable music market for the decade of the '80s, with cassette sales overtaking those of LPs. Total vinyl record sales remained higher well into the 1980s due to greater sales of singles, although cassette singles achieved popularity for a period in the 1990s. Another barrier to cassettes overtaking vinyl in sales was shoplifting; compact cassettes were small enough that a thief could easily place one inside a pocket and walk out of a shop without being noticed. To prevent this, retailers in the US would place cassettes inside oversized "spaghetti box" containers or locked display cases, either of which would significantly inhibit browsing, thus reducing cassette sales. During the early 1980s some record labels sought to solve this problem by introducing new, larger packages for cassettes which would allow them to be displayed alongside vinyl records and compact discs, or giving them a further market advantage over vinyl by adding bonus tracks. Willem Andriessen wrote that the development in technology allowed "hardware designers to discover and satisfy one of the collective desires of human beings all over the world, independent of region, climate, religion, culture, race, sex, age and education: the desire to enjoy music at any time, at any place, in any desired sound quality and almost at any wanted price". Critic Robert Palmer, writing in The New York Times in 1981, cited the proliferation of personal stereos as well as extra tracks not available on LP as reasons for the surge in popularity of cassettes.

Cassettes' ability to allow users to record content in public also led to a boom in bootleg cassettes made at live shows in the 1980s. The Walkman dominated the decade, selling up to 350 million units. So synonymous did the name "Walkman" become with all portable music players—with a German dictionary at one point defining the term as such without reference to Sony—that the Austrian Supreme Court ruled in 2002 that Sony, which had not sought to have the publisher of that dictionary retract that definition, could not prevent other companies from using that name, as it had now become genericized. As a result of this, a number of Sony's competitors produced their own version of the Walkman. Others made their own branded tape players, like JVC, Panasonic, Sharp, and Aiwa, the second-largest producer of the devices.

Between 1985, when cassettes overtook vinyl, and 1992, when they were overtaken by CDs (introduced in 1983 as a format that offered greater storage capacity and more accurate sound), the cassette tape was the most popular format in the United States and the UK. Record labels experimented with innovative packaging designs. A designer during the era explained: "There was so much money in the industry at the time, we could try anything with design." The introduction of the cassette single, called a "cassingle", was also part of this era and featured a music single in Compact Cassette form. Until 2005, cassettes remained the dominant medium for purchasing and listening to music in some developing countries, but compact disc (CD) technology had superseded the Compact Cassette in the vast majority of music markets throughout the world by this time.

Cassette culture

Compact cassettes served as catalysts for social change. Their small size, durability and ease of copying helped bring underground rock and punk music behind the Iron Curtain, creating a foothold for Western culture among the younger generations. Likewise, in Egypt cassettes empowered an unprecedented number of people to create culture, circulate information, and challenge ruling regimes before the internet became publicly accessible.

Cassettes at a Cairo Kiosk (2015)

One of the most famous political uses of cassette tapes was the dissemination of sermons by the exiled Ayatollah Khomeini throughout Iran before the 1979 Iranian Revolution, in which Khomeini urged the overthrow of the regime of the Shah, Mohammad Reza Pahlavi. During the military dictatorship of Chile (1973–1990) a "cassette culture" emerged where blacklisted music or music that was by other reasons not available as records was shared. Some pirate cassette producers created brands such as Cumbre y Cuatro that have in retrospect received praise for their contributions to popular music. Armed groups such as Manuel Rodríguez Patriotic Front (FPMR) and the Revolutionary Left Movement (MIR) made use of cassettes to spread their messages.

In 1970s India, cassettes were blamed for bringing unwanted Christian and Islamic influences into traditionally Sikh and Hindu areas. Cassette technology was a booming market for pop music in India, drawing criticism from conservatives while at the same time creating a huge market for legitimate recording companies, as well as pirated tapes. Some sales channels were associated with cassettes: in Spain filling stations often featured a display selling cassettes. While offering also mainstream music these cassettes became associated with genres such as Gipsy rhumba, light music and joke tapes that were very popular in the 1970s and 1980s.

Decline

Despite sales of CDs overtaking those of prerecorded cassettes in the early 1990s in the U.S., the format remained popular for specific applications, such as car audio, personal stereos, boomboxes, telephone answering machines, dictation, field recording, home recording, and mixtapes well into the decade. Cassette players were typically more resistant to shocks than CD players, and their lower fidelity was not considered a serious drawback in mobile use. With the introduction of electronic skip protection it became possible to use portable CD players on the go, and automotive CD players became viable. CD-R drives and media also became affordable for consumers around the same time.

By 1993, annual shipments of CD players had reached 5 million, up 21% from the year before; while cassette player shipments had dropped 7% to approximately 3.4 million. Sales of pre-recorded music cassettes in the US dropped from 442 million in 1990 to 274,000 by 2007. For audiobooks, the final year that cassettes represented greater than 50% of total market sales was 2002 when they were replaced by CDs as the dominant media.

The last new car with an available cassette player was a 2014 TagAZ AQUiLA. Four years prior, Sony had stopped the production of personal cassette players. In 2011, the Oxford English Dictionary removed the phrase "cassette player" from its 12th edition Concise version, which prompted some media sources to mistakenly report that the term "cassette tape" was being removed.

In India, music continued to be released on the cassette format due to its low cost until 2009.

21st century

Burmese music cassette tapes for sale, Yangon, Myanmar (2006)

Although portable digital recorders are most common today, analog tape remains a desirable option for certain artists and consumers. Artists and listeners of older genres like "dansband" may favor the format most familiar to their fans. Some musicians and DJs in the independent music community maintain a tradition of using and releasing cassettes due to its low cost and ease of use. Underground and DIY communities release regularly, and sometimes exclusively, on cassette format, particularly in experimental music circles and to a lesser extent in hardcore punk, death metal, and black metal circles, out of a fondness for the format. Even among major-label stars, the form has at least one devotee: Thurston Moore stated in 2009, "I only listen to cassettes." By 2019, few companies still made cassettes. Among those are National Audio Company, from the US, and Mulann, also known as Recording The Masters, from France.

Sony announced the end of cassette Walkman production on October 22, 2010, a result of the emergence of MP3 players such as Apple's iPod. Today Sony uses the Walkman brand solely for its line of digital media players, such as the NW-WM1ZM2, a high-end device released in 2022 for the niche audiophile market, which is manufactured with high quality components.

In 2010, Botswana-based Diamond Studios announced plans for establishing a plant to mass-produce cassettes in a bid to combat piracy. It opened in 2011.

In South Korea, the early English education boom for toddlers encourages a continuous demand for English language cassettes, as of 2011, due to the affordable cost.

National Audio Company in Missouri, the largest of the few remaining manufacturers of audio cassettes in the US, oversaw the mass production of the "Awesome Mix #1" cassette from the film Guardians of the Galaxy in 2014. They reported that they had produced more than 10 million tapes in 2014 and that sales were up 20 percent the following year, their best year since they opened in 1969. In 2016, cassette sales in the United States rose by 74% to 129,000. In 2018, following several years of shortage, National Audio Company began producing their own magnetic tape, becoming the world's first known manufacturer of an all-new tape stock. Mulann, a company which acquired Pyral/RMGI in 2015 and originates from BASF, also started production of its new cassette tape stock in 2018, basing on reel tape formula.

In Japan and South Korea, the pop acts Matsuda Seiko, SHINee, and NCT 127 released their material on limited-run cassettes.

In the mid-to-late 2010s, cassette sales saw a modest resurgence concurrent with the vinyl revival. As early as 2015, the retail chain Urban Outfitters, which had long sold LPs, started selling new pre-recorded cassettes (both new and old albums), blank cassettes, and players. In 2016, cassette sales increased, a trend that continued in 2017 and 2018. In the UK, sales of cassette tapes in 2021 reached its highest number since 2003.

Cassettes are favored by some artists and listeners, including those of older genres of music such as dansband, as well as independent and underground artists, some of whom were releasing new music on tape by the 2020s, including Britney Spears and Busta Rhymes. Reasons cited for this include tradition, low cost, the DIY ease of use, and a nostalgic fondness for how the format's imperfections lend greater vibrancy to low-fi, experimental music, despite the lack of the "full-bodied richness" of vinyl.

Features

Visualization of the magnetic field on a stereo cassette containing a 1kHz audio tone.

The cassette was a great step forward in convenience from reel-to-reel audio tape recording, although, because of the limitations of the cassette's size and speed, it initially compared poorly in quality. Unlike the 4-track stereo open-reel format, the two stereo tracks of each side lie adjacent to each other, rather than being interleaved with the tracks of the other side. This permitted monaural cassette players to play stereo recordings "summed" as mono tracks and permitted stereo players to play mono recordings through both speakers. The tape is 0.15 in (3.81 mm) wide, with each mono track 1.5 millimetres (0.059 in) wide, plus an unrecorded guard band between each track. In stereo, each track is further divided into a left and a right channel of 0.6 mm (0.024 in) each, with a gap of 0.3 mm (0.012 in). The tape moves past the playback head at 1+78 inches per second (4.76 cm/s), the speed being a continuation of the increasingly slower speed series in open-reel machines operating at 30, 15, 7+12, or 3+34 inches per second. For comparison, the typical open-reel 14-inch 4-track consumer format used tape that is 0.248 inches (6.3 mm) wide, each track .043 in (1.1 mm) wide, and running at either twice or four times the speed of a cassette.[citation needed]

Cassette types

Notches on the top surface of the Compact Cassette indicate its type. The rear-most cassette at the top of this picture, with only write-protect notches (here covered by write-protect tabs), is Type I, its tape consisting of iron oxide. The next cassette down, with additional notches adjacent to the write-protect tabs, is Type II, its tape consisting of chrome and cobalt. The bottom two cassettes, featuring the Type II notches plus an additional pair in the middle of the cassette, are Type IV (metal); note the removal of the tabs on the second of these, meaning the tape is write-protected. Type III was a combination of Types I and II but never gained the popularity of the other three types and was made obsolete by Type IV.

Cassette tapes are made of a polyester-type plastic film with a magnetic coating. The original magnetic material was based on gamma ferric oxide (Fe2O3). Circa 1970, 3M Company developed a cobalt volume-doping process combined with a double-coating technique to enhance overall tape output levels. This product was marketed as "High Energy" under its Scotch brand of recording tapes. Inexpensive cassettes commonly are labeled "low-noise", but typically are not optimized for high frequency response. For this reason, some low-grade IEC Type I tapes have been marketed specifically as better suited for data storage than for sound recording.[citation needed]

In 1968, DuPont, the inventor of a chromium dioxide (CrO2) manufacturing process, began commercialization of CrO2 media. The first CrO2 cassette was introduced in 1970 by Advent, and later strongly backed by BASF, the inventor and longtime manufacturer of magnetic recording tape. Next, coatings using magnetite (Fe3O4) such as TDK's Audua were produced in an attempt to approach or exceed the sound quality of vinyl records. Cobalt-adsorbed iron oxide (Avilyn) was introduced by TDK in 1974 and proved very successful. "Type IV" tapes using pure metal particles (as opposed to oxide formulations) were introduced in 1979 by 3M under the trade name Metafine. The tape coating on most cassettes sold today as either "normal" or "chrome" consists of ferric oxide and cobalt mixed in varying ratios (and using various processes); there are very few cassettes on the market that use a pure (CrO2) coating.

Simple voice recorders and earlier cassette decks are designed to work with standard ferric formulations. Newer tape decks usually are built with switches and later detectors for the different bias and equalization requirements for higher grade tapes. The most common are iron oxide tapes (defined by the IEC 60094 standard.

Notches on top of the cassette shell indicate the type of tape. Type I cassettes have only write-protect notches, Type II have an additional pair next to the write protection ones, and Type IV (metal) have a third set near the middle of the top of the cassette shell. These allow later cassette decks to detect the tape type automatically and select the proper bias and equalization.

Locating write-protect notches

If the cassette is held with one of the labels facing the user and the tape opening at the bottom, the write-protect notch for the corresponding side is at the top-left.

Tape length

Maxell compact cassettes, C60 (90m) and C90 (135m)

Tape length usually is measured in minutes of total playing time. The most popular varieties of blank tape were C60 (30 minutes per side), C90 (45 minutes per side) and C120 (60 minutes per side). The C46 and C60 lengths typically are 15 to 16 micrometers (0.59 to 0.63 mils) thick, but C90s are 10 to 11 μm (0.39 to 0.43 mils) and (the less common) C120s are just 6 μm (0.24 mils) thick, rendering them more susceptible to stretching or breakage. Even C180 tapes were available at one point.

Other lengths are (or were) also available from some vendors, including C10, C12 and C15 (useful for saving data from early home computers and in telephone answering machines), C30, C40, C50, C54, C64, C70, C74, C80, C84, C94, C100, C105, and C110. As late as 2010, Thomann still offered C10, C20, C30 and C40 IEC Type II tape cassettes for use with 4- and 8-track portastudios.

Track width

The full tape width is 3.8 mm. For mono recording the track width is 1.5 mm. In stereo mode each channel has width of 0.6 mm with a 0.3 mm separation to avoid crosstalk.

Head gap

The head-gap width[clarification needed] is 2 µm[according to whom?] which gives a theoretical maximum frequency[citation needed] of about 12 kHz (at the standard speed of 1 7/8 ips or 4.76 cm/s). A narrower gap would give a higher frequency limit but also weaker magnetization.

Cassette tape adapter

Cassette tape adapters allow external audio sources to be played back from any tape player, but were typically used for car audio systems. An attached audio cable with a phone connector converts the electrical signals to be read by the tape head, while mechanical gears simulate reel to reel movement without actual tapes when driven by the player mechanism.

Optional mechanical elements

Tape Guide via Security Mechanism (SM)

In order to wind up the tape more reliably, the former BASF (from 1998 EMTEC) patented the Special Mechanism or Security Mechanism advertised with the abbreviation SM in the early 1970s, which was temporarily used under license by Agfa. This feature each includes a rail to guide the tape to the spool and prevent an unclean roll from forming.

Flaws

Magnetic tape is not an ideal medium for long-term archival storage, as it begins to degrade after 10 – 20 years, with some experts estimating its lifespan to be no more than 30 years.

A common mechanical problem occurs when a defective player or resistance in the tape path causes insufficient tension on the take-up spool. This would cause the magnetic tape to be fed out through the bottom of the cassette and become tangled in the mechanism of the player. In these cases, the player was said to have "eaten" or "chewed" the tape, often destroying the playability of the cassette.[failed verification] Splicing blocks, analogous to those used for open-reel 1/4" tape, were available and could be used to remove the damaged portion or repair the break in the tape.[citation needed]

Cassette players and recorders

Tapematic 2002 audio cassette loaders, used to wind ("load") magnetic tape from tape reels ("pancakes") in the machine into empty cassette tape shells (known as C-0s or C-Zeros). The C-0s have just leader which is cut into two and the tape is attached to the leader, then wound.

The first cassette machines (e.g. the Philips EL 3300, introduced in August 1963)

Nakamichi RX-505 cassette deck. It has an auto reverse feature that rotates the cassette, hence the bump in the middle.

A major innovation was the front-loading arrangement. Pioneer's angled cassette bay and the exposed bays of some Sansui models eventually were standardized as a front-loading door into which a cassette would be loaded. Later models would adopt electronic buttons, and replace conventional meters (which could be "pegged" when overloaded[clarification needed]) with electronic LED or vacuum fluorescent displays, with level controls typically being controlled by either rotary controls or side-by-side sliders. BIC and Marantz briefly offered models that could be run at double speeds, but Nakamichi was widely recognized as one of the first companies to create decks that rivaled reel-to-reel decks with full 20–20,000 Hz frequency response, low noise, and very low wow and flutter.

Different interpretations of the cassette standard resulted in a 4 dB ambiguity at 16 kHz. Technically, both camps in this debate were still within the original cassette specification as no tolerance for frequency response is provided above 12.5 kHz and all calibration tones above 12.5 kHz are considered optional. Decreasing noise at 16 kHz also decreases the maximum signal level at 16 kHz, the High-Frequency Dynamics stay almost constant.

A third company, Bang & Olufsen of Denmark, created the Dolby HX "head room extension" system for reliably reducing tape saturation effects at high frequencies while maintaining higher bias levels.

Radio–cassette players of the design also called "ghetto-blasters" and "boomboxes"

Applications for car stereos varied widely. Auto manufacturers in the US typically would fit a cassette slot into their standard large radio faceplates. Europe and Asia would standardize on DIN and double DIN sized faceplates. In the 1980s, a high-end installation would have a Dolby AM/FM cassette deck, and they rendered the 8-track player obsolete in car installations because of space, performance, and audio quality. In the 1990s and 2000s, as the cost of building CD players declined, many manufacturers offered a CD player. The CD player eventually supplanted the cassette deck as standard equipment, but some cars, especially those targeted at older drivers, were offered with the option of a cassette player, either by itself or sometimes in combination with a CD slot. Most new cars can still accommodate aftermarket cassette players, and the auxiliary jack advertised for MP3 players can be used also with portable cassette players, but 2011 was the first model year for which no manufacturer offered factory-installed cassette players.

A head cleaning cassette

Applications

Audio

A dual cassette-based Panasonic answering machine

The Compact Cassette originally was intended for use in dictation machines. In this capacity, some later-model cassette-based dictation machines could also run the tape at half speed (1516 in/s) as playback quality was not critical. The cassette soon became a popular medium for distributing prerecorded music—initially through the Philips Record Company (and subsidiary labels Mercury and Philips in the US). As of 2009, one still found cassettes used for a variety of purposes, such as journalism, oral history, meeting and interview transcripts, audio-books, and so on. Police are still big buyers of cassette tapes, as some lawyers "don't trust digital technology for interviews". However, they are starting to give way to Compact Discs and more "compact" digital storage media. Prerecorded cassettes were also employed as a way of providing chemotherapy information to recently diagnosed cancer patients as studies found anxiety and fear often gets in the way of the information processing.

The cassette quickly found use in the commercial music industry. One artifact found on some commercially produced music cassettes was a sequence of test tones, called SDR (Super Dynamic Range, also called XDR, or eXtended Dynamic Range) soundburst tones, at the beginning and end of the tape, heard in order of low frequency to high. These were used during SDR/XDR's duplication process to gauge the quality of the tape medium. Many consumers objected to these tones since they were not part of the recorded music.

Home studio

In the simplest configuration, rather than playing a pair of stereo channels of each side of the cassette, the typical "portastudio" used a four-track tape head assembly to access four tracks on the cassette at once (with the tape playing in one direction). Each track could be recorded to, erased, or played back individually, allowing musicians to overdub themselves and create simple multitrack recordings easily, which could then be mixed down to a finished stereo version on an external machine. To increase audio quality in these recorders, the tape speed sometimes was doubled to 33/4 inches per second, in comparison to the standard 178 ips; additionally, dbx, Dolby B or Dolby C noise reduction provided compansion (compression of the signal during recording with equal and opposite expansion of the signal during playback), which yields increased dynamic range by lowering the noise level and increasing the maximum signal level before distortion occurs. Multi-track cassette recorders with built-in mixer and signal routing features ranged from easy-to-use beginner units up to professional-level recording systems.

Home dubbing

A Magnavox dual deck recorder with high-speed dubbing. Doors are open showing capstans.

Most cassettes were sold blank, and used for recording (dubbing) the owner's records (as backup, to play in the car, or to make mixtape compilations), their friends' records, or music from the radio. This practice was condemned by the music industry with such alarmist slogans as "Home Taping Is Killing Music". However, many claimed that the medium was ideal for spreading new music and would increase sales, and strongly defended their right to copy at least their own records onto tape. For a limited time in the early 1980s Island Records sold chromium dioxide "One Plus One"

Various legal cases arose surrounding the dubbing of cassettes. In the UK, in the case of CBS Songs v. Amstrad (1988), the House of Lords found in favor of Amstrad that producing equipment that facilitated the dubbing of cassettes, in this case a high-speed twin cassette deck that allowed one cassette to be copied directly onto another, did not constitute copyright infringement by the manufacturer. In a similar case, a shop owner who rented cassettes and sold blank tapes was not liable for copyright infringement even though it was clear that his customers likely were dubbing them at home. In both cases, the courts held that manufacturers and retailers could not be held accountable for the actions of consumers.

As an alternative to home dubbing, in the late 1980s, the Personics company installed booths in record stores across America that allowed customers to make personalized mixtapes from a digitally encoded back-catalogue with customised printed covers.

Data recording

A C2N Datassette recorder for Commodore computers
A streamer cassette for data storage, adapted from the audio Compact Cassette format

Floppy disk storage had become the standard data storage medium in the United States by the mid-1980s; for example, by 1983 the majority of software sold by Atari Program Exchange was on floppy. Cassette remained more popular for 8-bit computers such as the Commodore 64, ZX Spectrum, MSX, and Amstrad CPC 464 in many countries such as the United Kingdom (where 8-bit software was mostly sold on cassette until that market disappeared altogether in the early 1990s). Reliability of cassettes for data storage is inconsistent, with many users recalling repeated attempts to load video games; the Commodore Datasette used very reliable, but slow, digital encoding. In some countries, including the United Kingdom, Poland, Hungary, and the Netherlands, cassette data storage was so popular that some radio stations would broadcast computer programs that listeners could record onto cassette and then load into their computer. See BASICODE.[citation needed]

The cassette was adapted into what is called a streamer cassette (also known as a "D/CAS" cassette), a version dedicated solely for data storage, and used chiefly for hard disk backups and other types of data. Streamer cassettes look almost exactly the same as a standard cassette, with the exception of having a notch about one quarter-inch wide and deep situated slightly off-center at the top edge of the cassette. Streamer cassettes also have a re-usable write-protect tab on only one side of the top edge of the cassette, with the other side of the top edge having either only an open rectangular hole, or no hole at all. This is due to the entire one-eighth inch width of the tape loaded inside being used by a streamer cassette drive for the writing and reading of data, hence only one side of the cassette being used. Streamer cassettes can hold anywhere from 250 kilobytes to 600 megabytes of data.

Rivals and successors

Size comparison of Elcaset (left) with standard Compact Cassette

Technical development of the cassette effectively ceased when digital recordable media, such as DAT and MiniDisc, were introduced in the late 1980s and early-to-mid 1990s, with Dolby S recorders marking the peak of Compact Cassette technology. Anticipating the switch from analog to digital format, major companies, such as Sony, shifted their focus to new media. In 1992, Philips introduced the Digital Compact Cassette (DCC), a DAT-like tape in almost the same shell as a Compact Cassette. It was aimed primarily at the consumer market. A DCC deck could play back both types of cassettes. Unlike DAT, which was accepted in professional usage because it could record without lossy compression effects, DCC failed in home, mobile and professional environments, and was discontinued in 1996.

A Compact Cassette and a Microcassette

The microcassette largely supplanted the full-sized cassette in situations where voice-level fidelity is all that is required, such as in dictation machines and answering machines. Microcassettes have in turn given way to digital recorders of various descriptions. Since the rise of cheap CD-R discs, and flash memory-based digital audio players, the phenomenon of "home taping" has effectively switched to recording to a Compact Disc or downloading from commercial or music-sharing websites.

Because of consumer demand, the cassette has remained influential on design, more than a decade after its decline as a media mainstay. As the Compact Disc grew in popularity, cassette-shaped audio adapters were developed to provide an economical and clear way to obtain CD functionality in vehicles equipped with cassette decks but no CD player. A portable CD player would have its analog line-out connected to the adapter, which in turn fed the signal to the head of the cassette deck. These adapters continue to function with MP3 players and smartphones, and generally are more reliable than the FM transmitters that must be used to adapt CD players and digital audio players to car stereo systems. Digital audio players shaped as cassettes have also become available, which can be inserted into any cassette player and communicate with the head as if they were normal cassettes.

See also

Further reading

  • Marc Masters. 2023. High Bias: The Distorted History of the Cassette Tape. University of North Carolina Press.

This page was last updated at 2024-03-17 10:35 UTC. Update now. View original page.

All our content comes from Wikipedia and under the Creative Commons Attribution-ShareAlike License.


Top

If mathematical, chemical, physical and other formulas are not displayed correctly on this page, please useFirefox or Safari